Archives par étiquette : AirMax

AirOS V5.2.1-BETA 3 disponible

Nouvelle version pour le firmware AirOS destiné aux modules Airmax d’Ubiquiti, en version 5.2.1 Beta 3 désormais. Les changements, in english :

– Major: Station stays connected to AP, but no wireless traffic is available
– Major: Multicast traffic improvements
– Minor: PowerAP N WLAN LED is not shining when RSSI level is less than 30

– GUI: Speed tests doesn’t work if HTTPS port has been changed
– GUI: When disabling scan list, previously selected channels are unchecked
– GUI: new Chrome-BETA conflicts with Web UI validation framework
– GUI: Fixed rates uses SGI(400ns) rate table
– GUI: Read only user can access device configuration file
– GUI: Option to disable reset button. Prevents from accidental configuration reset to factory defaults
– GUI: Sometimes Station list is empty

à télécharger sur ce lien : http://ubnt.com/downloads/XN-fw-inte…00715.1855.bin

Largeur de bande et accessibilité

Une mauvaise configuration revient régulièrement sur les modules Ubiquit à la norme Airmax : Bullet M, Nanostation M, etc.

Il arrive en effet souvent qu’un module Bullet M2 (2.4 GHz) soit configuré avec une largeur de bande de 40 MHz : il est du coup parfaitement bien reçu sur la plupart des matériels obéissant à la norme 802.11n mais pas du tout sur les « anciens » matériels…

La solution ? Basculer sur une largeur de 20 MHz, largement suffisante puisqu’elle vous permet une connexion de 54 Mbps, largement en deça des capacités de 99% des lignes ADSL 😉

AirOS V5.2 : réglez la puissance

Le firmware AirOS V5.2 permet désormais d’effectuer un réglage semi-automatique de la puissance émise par le module, tenant compte du gain de l’antenne, des pertes d’un éventuel câble coaxial, du pays d’utilisation, et pour finir, de la fréquence utilisée.

De ce fait, vous ne risquez pas de vous retrouver hors la loi en utilisant votre matériel, le firmware calcule tout pour vous, en espérant qu’il soit correctement paramétré, c’est une autre histoire…

Voici une vidéo réalisée avec un Bullet 5M, présentant cette nouvelle fonctionnalite, à visualiser si possible en HD pour plus de détails. Vous y verrez un changement de canal, un blocage de la puissance par le firmware, un changement de gain d’antenne avec un nouveau changement de puissance max, etc.

AirOS V5.2.1-Beta2 disponible

Ce jour sort la version AirOS V5.2.1-Beta 2, la suite des évolutions logicielles du firmware destiné aux matériels Airmax d’Ubiquiti.

Les modifications sont :

v5.2.1-Beta2 Changelog:
– Show static routes in Main page, when operating in Bridge mode
– Station list is empty on IE browser
– Sometimes after AP reboot or FW upgrade, station cannot associate to AP anymore (security ON)

V5.2.1-Beta Changelog:

– Multicast enhancement on AP problems for multicast traffic (RSTP/OSPF doesn’t pass wireless link)
– Multicast traffic floods entire office network
– Multicast packets in AP WDS – AP WDS setup are transmitted with 3 addresses
– IGMP proxy improvements
– CCR: Increase maximum allowed DHCP server lease time to 48h
– CCR: Allow more than 128 associations with security off
– AirControl Agent: Restore console reporting after wireless association is restored
– AirControl Agent: Report association time
– AirControl Agent: Odd behaviour with discovery response

MAJOR fixes:

– Wireless stability fixes
– WPA group key handshake failure
– AP is using the lowest TX rate (6Mbps), when communicating to legacy Stations and using WEP/WPA-TKIP/WPA2-TKIP security
– Incorrect data rates when operating in AP-WDS/AP-WDS and HT40 mode
– Incorrect frame type or subtype received from unauthenticated station (6)
– PPPoE client isn’t restoring session after lost wireless link connection
– « MAC Address » change in Station-Router mode results WPA failure
– Devices behind STA-WDS in PtMP network, sometimes becomes unreachable
– Fix: SNMP: Report correct IF-MIB interface speed OID values
– Updated Australia regulatory rules according ACMA
– AP scans only upper or lower channels in HT40 mode
– AP(WDS) HT40 can connect AP(WDS) HT20
– GUI improvements

Pour télécharger, rendez-vous ici : http://ubnt.com/downloads/XN-fw-internal/v5.2.1-beta/XM.v5.2.1-beta2.5355.100604.1558.bin

AirOS V5.2 disponible

Les versions Beta se sont succédées à un rythme effréné ces dernières semaines, il était donc tout à fait logique de s’attendre à une version toute neuve ! Voilà qui est fait, avec AirOS V 5.2, destiné à tous les modules Ubiquiti disposant de la fonctionnalité Airmax : Bullet 2M & 5M, Nanostation 2M & 5M, Rocket 2M et 5M, etc.

Les changements récents sont :

V5.2-RC Changelog:

– Fix: Sometimes Auto ACK values gets too high
– Fix: Max power level for Australia
– GUI fix: Name -> Device Name
– GUI fix: Grammar error in warning message

V5.2-Beta8 Changelog:

– Fix: Speed test + AirMax PtP No Ack combination crashes AP
– Fix: Traffic Shaping is not functional except Soho Router mode
– Fix: Traffic Shaping Burst is for functional
– Fix: WPA security : Sometimes station is disassociated from AP
– Fix: Broadcast traffic is duplicated on AP-WDS
– Fix: NAT protocols state changes when changing security
– Fix: SNMP wrong OID type- Fix: Disallow port range as destination (to private subnet)
– Fix: Station can not connect to AP (MAC Locked) if it was connected to another AP with the same SSID
– Fix: Airmax PTMP ping loss issue after beta6
– Fix: AirMax: PTPNack AMQ/AMC fluctuation
– Fix: TX Power improvement for NanoBridge M5, AirGridM5, LocoM5, Bullet M2, Rocket M2, NanoStationM2, NanoBridge M2)
– Fix: AirMax: PTP and PTMP enhancements (latency)

– GUI: Problems with WPA PSK paraphrase: old value is displayed, new value is not saved
– GUI: Sometime Device name in not reported in Stations list
– GUI: Do not show clients as connected when authentication key is not valid
– GUI: Test mode. Timing is no so precise as stated in the warning message
– GUI: Need correctly display ACK/Distance when AirMax and PtPNoACK mode is enabled
– CCR: Report AirMax priority and AMQ/AMC in Station detail

—> Limitation from HW: MCS13 does not work with WEP/WPA/WPA2/WPA-TKIP/WPA2-TKIP security — MCS 13 removed from WEB UI

V5.2-Beta7:

– Improvement: Power control fix
– Improvement: AirMax: PTP and PTMP latency improvements
– Improvement: Speed test – resolves TX/RX difference
– Fix: SNMP reports incorrect wireless stats

– CCR: Speed test: Show total throughput (RX + TX)
– CCR: Make IP address in stations list as hyperlink
– CCR: GUI: Show/hide Traffic shaping configuration
– CCR: GUI: Add option to enable/disable NAT modules on router: SIP, PPTP, FTP, RTSP
– Fix: MCS1 is always reported in AP/Station statistics

Rendez-vous sur la page de téléchargement pour récupérer la version 5.2.

AirOS 5.2Beta8 disponible

La nouvelle version Beta d’AirOS est disponible depuis le 7 Mai, avec comme changements :

– Fix: Speed test + AirMax PtP No Ack combination crashes AP
– Fix: Traffic Shaping is not functional except Soho Router mode
– Fix: Traffic Shaping Burst is for functional
– Fix: WPA security : Sometimes station is disassociated from AP
– Fix: Broadcast traffic is duplicated on AP-WDS
– Fix: NAT protocols state changes when changing security
– Fix: SNMP wrong OID type- Fix: Disallow port range as destination (to private subnet)
– Fix: Station can not connect to AP (MAC Locked) if it was connected to another AP with the same SSID
– Fix: Airmax PTMP ping loss issue after beta6
– Fix: AirMax: PTPNack AMQ/AMC fluctuation
– Fix: TX Power improvement for NanoBridge M5, AirGridM5, LocoM5, Bullet M2, Rocket M2, NanoStation M2, NanoBridge M2)
– Fix: AirMax: PTP and PTMP enhancements (latency)

– GUI: Problems with WPA PSK paraphrase: old value is displayed, new value is not saved
– GUI: Sometime Device name in not reported in Stations list
– GUI: Do not show clients as connected when authentication key is not valid
– GUI: Test mode. Timing is no so precise as stated in the warning message
– GUI: Need correctly display ACK/Distance when AirMax and PtPNoACK mode is enabled
– CCR: Report AirMax priority and AMQ/AMC in Station detail :
—> Limitation from HW: MCS13 does not work with WEP/WPA/WPA2/WPA-TKIP/WPA2-TKIP security — MCS 13 removed from WEB UI

A découvrir en suivant ce lien : http://ubnt.com/downloads/XN-fw-internal/v5.2-BETA/XM.v5.2-beta8.5008.100507.1641.bin

AirOS 5.2 Beta 7 disponible

J’admire sincèrement la réactivité d’Ubiquiti quant au firmware AirOS : voici déjà la version 5.2 Beta 7, peu de temps après la Beta 6.

Les nouveautés :

– Improvement: Power control fix
– Improvement: AirMax: PTP and PTMP latency improvements
– Improvement: Speed test – resolves TX/RX difference
– Fix: SNMP reports incorrect wireless stats

– CCR: Speed test: Show total throughput (RX + TX)
– CCR: Make IP address in stations list as hyperlink
– CCR: GUI: Show/hide Traffic shaping configuration
– CCR: GUI: Add option to enable/disable NAT modules on router: SIP, PPTP, FTP, RTSP
– Fix: MCS1 is always reported in AP/Station statistics

Et pour télécharger, par ici : http://www.ubnt.com/downloads/XN-fw-…00423.1708.bin

Rocket 5 ? Débits réels ?

Beaucoup doutent des possibilités d’un bridge Rocket 5 quant au débit et à la distance atteignable.

Voici ce qu’un utilisateur a récemment indiqué sur un forum :

« I have a 41 km link with rocket m5 and rocket dishes on 40 mhz channel width and airmax enabled.
Throughput: 90 mbps in one way and 45 in duplex. »

En plus clair, et en français, 41 km avec un Rocket 5 et une parabole, un canal de 40 MHz, Airmax activé, et un débit simplex de 90 MBps, 45 en duplex intégral.

Plutôt pratique non ? 🙂

Vieilles Charrues 2010 & Ubiquiti

Quel rapport entre les Vieilles Charrues et les modules Ubiquiti ? L’utilisation de deux Nanostation 5M pour assurer une liaison vidéo en direct pour le compte de la radio RMN !

C’est en effet sur une distance d’environ 200 à 300 m qu’une liaison à 125 Mbps a été établie sur 5 GHz, reliée d’un côté à une ligne SDSL et de l’autre au matériel vidéo servant  à retransmettre en direct la conférence de presse annonçant la programmation 2010.

La vidéo en question se trouve ici et la programmation 2010 sur le site des Vieilles Charrues.